| 121.45.5000.990.41.1502 Standard 5 Slewing Ring Bearings | Cb min.:6 mm; Mass bearing:1.31 kg; r1,2 min.:2.5 mm; Calculation factor e:0.35; ra max.:2.5 mm; Dimension series:2ED; D:100 mm; Reference speed:5600 r/min; T:36 mm; B:35 mm; db min.:61 mm; Da max.:90 mm; Limiting speed:6700 r/min; C:30 mm; Db min.:94 mm; Basic static load rating C0:200 kN; Da min.:84 mm; Calculation factor Y:1.7; d:50 mm; a:24.464 mm; |
| 121.50.6700.990.41.1502 Standard 5 Slewing Ring Bearings | Limiting speed:2800 r/min; Basic dynamic load rating C:332 kN; Db max.:311 mm; D:320 mm; Mass bearing:26 kg; d:150 mm; Calculation factor Y0:0.52; Calculation factor X:0.35; Calculation factor Y1:0.55; d1 ≈:216.1 mm; D1 ≈:258.65 mm; Calculation factor Y2:0.93; B:65 mm; rb max.:1.5 mm; Calculation factor A:2.74; da min.:167 mm; ra max.:3 mm; r3,4 min.:1.5 mm; Fatigue load limit Pu:10.8 kN; |
| 162.36.2000.891.41.1503 Standard 5 Slewing Ring Bearings | Cap bolt:2 x 3/4-10 UNC; A1:111.125 mm; Initial grease fill:481.95 g; Mass pillow block:41.1 kg; PG:1/4 NPT; R1:73.025 mm; P90°:77 kN; P120°:48.9 kN; Appropriate attachment bolt size G:0.75 in; L:393.7 mm; N1:22.225 mm; Taconite seal:TER 189; Cap bolt, SAE grade:8; P60°:128 kN; R2:28.575 mm; RG:3/8 NPT; A2:231.775 mm; Cap bolt recommended tightening torque:515.2 N·m; da:82.55 mm; |
| 39 0411 01 Rollix Slewing Ring Bearings | Limiting speed for lubrication with:0 min-1; D1:mm; Pu:570 kN; D:220 mm; Oil:111.350 kN; B1:mm; Static (Cor):73 mm; d:130 mm; Weight:0 min-1; Grease:1080 kN; B2 B Dynamic (Cr):mm; |
| 161.40.2128.891.41.1503 Standard 5 Slewing Ring Bearings | Basic static load rating C0:200 kN; G:M 42x3; d2 max.:104 mm; Mass rod end:2.45 kg; d:45 mm; Material constant KM:330; r1 min.:0.6 mm; dk:60 mm; h:163 mm; Specific dynamic load factor K:150 N/mm²; l2 max.:217 mm; B:32 mm; α:7 °; l7 min.:50 mm; C1 max.:28 mm; l1 min.:92 mm; Basic dynamic load rating C:190 kN; |
| 162.45.2510.890.11.1503 Standard 5 Slewing Ring Bearings | Tolerance shaft:h8; Specific dynamic load factor K:10 N/mm²; Coefficient of friction µ min.:0.05; D1:65 mm; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; D:55 mm; B:45 mm; Permissible sliding velocity v min.:0.25 m/s; Mass bushing:0.25 kg; d:45 mm; Specific static load factor K0:20 N/mm²; B1:5 mm; Tolerance housing:H7; |
| 92.35.1704.991.41.1502 Standard 5 Slewing Ring Bearings | A1:88.9 mm; Cap bolt recommended tightening torque:298.3 N·m; Stabilizing ring:SR-17-14; S:4.763 mm; da:74.612 mm; Cap bolt, SAE grade:8; Initial grease fill:110.56 g; R2:22.225 mm; RG:3/8 NPT; R1:53.975 mm; L:330.2 mm; H:187.325 mm; ba:35.719 mm; Mass pillow block:24.9 kg; Max. speed for Taconite seal:1050 r/min; P90°:47.2 kN; Housing:SSAFS 517; P180°:32 kN; P120°:28.9 kN; Pa:9.25 kN; |
| 162.45.2366.890.11.1503 Standard 5 Slewing Ring Bearings | Pu:2.032 kN; da:65 min; rs:2 mm; d:55 mm; Dynamic (Cr):71.000 kN; B:29 mm; Static (Cor):44.700 kN; ra:2 max; Weight:1.38 kg; Bearing designation:6311 ; D:120 mm; Oil:6 700 min-1; Grease:5 600 min-1; Da:110 max; |
| 12.30.2538.001.41.1503 Standard 5 Slewing Ring Bearings | Mass bushing:0.11 kg; D:32 mm; Specific dynamic load factor K:10 N/mm²; Tolerance shaft:h8; Specific static load factor K0:20 N/mm²; Coefficient of friction µ max.:0.1; Coefficient of friction µ min.:0.05; B:30 mm; Permissible sliding velocity v max.:5 m/s; Permissible sliding velocity v min.:0.25 m/s; d:16 mm; Tolerance housing:H7; |
| 161.45.2366.890.11.1503 Standard 5 Slewing Ring Bearings | Limiting speed:700 r/min; ra max.:2 mm; das:384 mm; Da max.:429 mm; r1,2 min.:2.1 mm; Mass bearing:11.5 kg; d:360 mm; Reference speed:560 r/min; Calculation factor kr:0.1; Calculation factor Y:0.6; E:418.9 mm; D:440 mm; Fatigue load limit Pu:76.5 kN; s max.:3 mm; B:38 mm; Basic static load rating C0:900 kN; Basic dynamic load rating C:402 kN; Db max.:433 mm; d1 ≈:388 mm; Calculation factor e:0.2; |
| 161.40.2368.891.41.1503 Standard 5 Slewing Ring Bearings | r3,4 min.:1 mm; b1:6 mm; d:110 mm; Fatigue load limit Pu:95 kN; Da max.:161 mm; Mass bearing:6.32 kg; r1,2 min.:2 mm; Limiting speed:2200 r/min; B:80 mm; s max.:5 mm; Calculation factor kr:0.5; Basic static load rating C0:800 kN; Basic dynamic load rating C:512 kN; das:124 mm; D1 ≈:148.5 mm; da min.:120 mm; Reference speed:1800 r/min; K:3.5 mm; D:170 mm; ra max.:2 mm; |
| 11.30.2235.000.11.1503 Standard 5 Slewing Ring Bearings | P60°:226 kN; P180°:94.3 kN; J min.:441.325 mm; N1:28.575 mm; Initial grease fill:793.8 g; Pa:49.8 kN; RG:3/4 NPT; Cap bolt:4 x 3/4-10 UNC; R1:104.775 mm; P90°:136 kN; H2:66.675 mm; Max. speed for Taconite seal:560 r/min; Appropriate attachment bolt size G:1 in; Da:289.999 mm; Cap bolt recommended tightening torque:203.4 N·m; h:52.388 mm; J1:95.25 mm; Stabilizing ring:SR-32-0; P120°:85.9 kN; |
| 191.40.4500.990.41.1502 Standard 5 Slewing Ring Bearings | C:35 mm; Recommended tighthening torque:450 N·m; B2:15 mm; G1:32 mm; Basic static load rating C0:122 kN; G:M 30x1.5; D:90 mm; Grease fitting:NIP A3x9.5; Hexagonal nut:M 30x1.5; B1:63 mm; Lubrication adapter:AP 14; Maximum static radial loads F0r max.:260 kN; M:8 mm; SW:14 mm; B:100 mm; M1:4 mm; Basic dynamic load rating C:47.3 kN; Limiting speed:1400 r/min; Maximum dynamic radial loads Fr max.:183 kN; |
| 191.25.2000.990.41.1502 Standard 5 Slewing Ring Bearings | Housing:FSAF 516; Cap bolt:2 x 5/8-11 UNC; Cap bolt, SAE grade:5; J min.:244.475 mm; J1:53.975 mm; P60°:60.5 kN; S:4.763 mm; Stabilizing ring:SR-16-13; Initial grease fill:87.885 g; Ca:42.799 mm; R1:53.181 mm; Mass pillow block:17.4 kg; N1:19.05 mm; PG:1/8 NPT; ba:34.131 mm; H2:31.75 mm; P90°:36 kN; P120°:21.8 kN; P150°:19.6 kN; da:68.263 mm; |
| No. | Brand | M | F | J | b | K | B | N | D |
| 12.35.1960.400.11.1503 | Standard 5 | - | - | - | - | - | 90 mm | - | 160 mm |
| 121.50.5600.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.35.1750.700.11.1503 | Standard 5 | - | - | - | - | - | 13 mm | - | 90 mm |
| 12.30.1995.000.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 11.35.2620.001.41.1503 | Standard 5 | - | - | - | - | - | 11.379 mm | - | - |
| 12.40.2950.000.11.1502 | Standard 5 | - | - | - | - | - | 28.042 mm | - | - |
| 92.40.2199.990.11.1502 | Standard 5 | - | - | - | - | - | 20 mm | - | 39 mm |
| 121.45.5300.990.41.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 8 0307 | Rollix | - | - | - | - | - | - | - | 340 mm |
| 191.40.3150.990.41.1502 | Standard 5 | - | - | - | - | 12 mm | 148 mm | - | - |
| 11.40.3150.000.11.1502 | Standard 5 | - | - | - | - | - | - | - | - |
| 8 0220 05 | Rollix | - | - | - | - | - | 28 mm | - | - |
| 91.40.2199.991.41.1502 | Standard 5 | - | - | - | - | - | 224 mm | - | 620 mm |
| 162.40.2128.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 91.50.2644.990.41.1502 | Standard 5 | - | 170 mm | - | mm | - | 35 mm | - | 225 mm |
| 162.50.2660.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 12.30.2538.000.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 162.36.1800.890.11.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 61.40.1600.008.19.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 161.50.2800.891.41.1503 | Standard 5 | - | - | - | - | - | - | - | - |
| 1 0235 | Rollix | - | - | - | - | - | - | - | 95 mm |
| 91.40.2003.990.11.1502 | Standard 5 | - | 12 mm | - | - | - | 12.5 mm | - | - |
| 11.40.2795.000.11.1502 | Standard 5 | - | - | - | - | - | 67 mm | - | 260 mm |
| 91.50.2842.990.41.1502 | Standard 5 | - | - | - | - | - | 23 mm | - | 120 mm |
| 61.50.2130.001.49.1504 | Standard 5 | - | - | - | - | - | 6 mm | - | 19 mm |
| 11.40.2915.000.11.1502 | Standard 5 | - | - | - | - | - | 35 mm | - | - |
| 33 0411 01 | Rollix | - | 445 mm | - | 16.7 mm | - | 205 mm | - | 560 mm |
| 7 0380 01 | Rollix | - | - | - | - | - | - | - | - |
| 3 0217 | Rollix | - | 60 mm | - | - | - | 25 mm | - | - |
1 0181 02 Rollix Slewing Ring Bearings Video
April 2022 - Examinations Council of Lesotho
6 days ago — Assessment of Grades 1, 2 and 3 in Lesotho. In August 2014 the Ministry of Education and Training, Lesotho, contracted the Australian ...
encitech DB15-SP-K 2101-0181-02 D-SUB pin strip 180 ...
encitech DB15-SP-K 2101-0181-02 D-SUB pin strip 180 ° Number of pins: 15 Solder bucket 1 pc(s) Tray ... 1 piece, 3,59 € ... 2101-0181-02; EAN: 2050005912363.1 piece: 3,59 €5+ pieces: 3,48 €10+ pieces: 3,41 €50+ pieces: 3,23 €
Installation of Magnetic Pickups - FW Murphy
00-02-0181 rev. 2019/12/20 ... MP7905 and MP7906: Type 6061 Aluminum/Anodize Class 1 ... TEF insulated per MIL-W-16878D Type E, 1 White and 1 Black.2 pages
Shurflo Straight Fitting Wingnut Swivel - 1/2"-14NPT(F) x 5/8 ...
Shurflo by Pentair Straight Fitting Wingnut Swivel - 1/2"-14NPT(F) x 5/8"Barb - 94-181-02.
Subway 181, 02/18 Hillside Avenue Suite 1, Jamaica, NY 11432
Rate your experience! $ • Sandwich Shops. Hours: 9AM - 11PM 181, 02/18 Hillside Avenue Suite 1, Jamaica
Subway - 181-02/18 Hillside Avenue, Suite 1 - Foursquare
See 6 photos from 112 visitors to Subway.
Damage Disclosure Statement
MVR-181. (Rev. 02/2022). DAMAGE DISCLOSURE STATEMENT. Questions 1 & 4 apply only to five (5) model years old and newer. Alterations or erasures void this ...1 page
SUBWAY at 181-02/18 Hillside Avenue Jamaica NY
Your local Jamaica Subway® Restaurant, located at 181-02/18 Hillside Avenue brings delicious ingredients and mouth-watering flavors in billions of sandwich, ...
Application for Tax Clearance Certificate (REV-181) - PA ...
1. (Please submit copy of 501(c) exemption letter) ... REV-181 (CM) 02-21 ... of Revenue (address on Page 1) and one copy to the PA dePARTMenT OF LABOR &.4 pages